large long cylinder Sold to Qatar

This article mainly introduces:

Qatar hydraulic cylinder,large long cylinder manufacturer,large long cylinder

(Qatar large long cylinder,produced by Hengyu Hydraulic Co., Ltd）

large long cylinder are widely used in Qatar，because of no need for deceleration device，high work efficiency，excellent fatigue and impact resistance.So our company has designed large long cylinder for customers from Qatar.

Introduction to large long cylinder:

The assembly work of the large long cylinder has a great impact on the quality of the large long cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the large long cylinder is installed, the piston and the large long cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the large long cylinder head boss is easy to cause scars when it hits the inner surface of the large long cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized large long cylinders, only careful and careful operation can be avoided.

In the process of using the large long cylinder, sometimes such a problem will occur, the large long cylinder can not act immediately after the instruction of the large long cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil large long cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When the oil pressure of the large long cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about large long cylinder:

Why manual forklift oil cylinder can not lift up?
Manual hydraulic forklift truck often can not be pressed up, there are several reasons: for manual hydraulic truck: 1) There is no hydraulic oil 2) the purity of the oil is not enough 3) the adjusting bolt is too close or the adjusting screw is too tight, so that the valve is always open, 4) there is an air in the hydraulic cylinder. Method: 1) Refueling 2) Oil change 3) air discharge. For manual hydraulic stacker, also called manual lift car 1) Less than the amount of oil 2) impurities in the hydraulic oil, so that the check valve can not be closed. Method 1) Add enough hydraulic oil 2) Remove the cylinder, screw off the bottom plate, remove the impurities in the bottom plate.

To achieve the same stroke, which is better, hydraulic cylinder or lead screw?
If there is batch action, then the hydraulic pressure is better. Hydraulic: smooth operation, no lubrication, easy control, high control accuracy (can use proportional or servo system), the key is to manually control, but certainly to support the hydraulic system, for a single action must cost. Maintenance costs are also high. Lead screw: simple structure, easy to achieve, convenient maintenance, but must be lubricated, can not be manual, or manual control is inconvenient. See where it is used, if it is used in high-precision occasions, it must only be hydraulic, because the lead screw has a gap. There are many hydraulic actions, the hydraulic system itself must be prepared, then the use of hydraulic pressure is also very economical.