stern plate hydraulic cylinder Sold to Azerbaijan

This article mainly introduces:

Azerbaijan hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

(Azerbaijan stern plate hydraulic cylinder,produced by Hengyu Group）

stern plate hydraulic cylinder are widely used in Azerbaijan，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed stern plate hydraulic cylinder for customers from Azerbaijan.

Introduction to stern plate hydraulic cylinder:

The role of the stern plate hydraulic cylinder in the mold industry: the stern plate hydraulic cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the stern plate hydraulic cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The stern plate hydraulic cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

If the stern plate hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The scar on the sliding surface of the stern plate hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the stern plate hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

The stern plate hydraulic cylinder should be vented: when the stern plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the stern plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the stern plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the stern plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the stern plate hydraulic cylinder. stern plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Answers to some questions about stern plate hydraulic cylinder:

How to calculate the cross-sectional area of hydraulic cylinder?
Hydraulic cylinder cross section integral rod cavity and rodless cavity: rod cavity is cylinder inner wall cross-sectional area - piston rod cross-sectional area; The rodless cavity is the cross-sectional area of the inner wall of the cylinder. If the working pressure p and the output force F are known, the effective cross-sectional area A=F/p can be calculated.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.