series synchronous cylinder Sold to New Zealand

This article mainly introduces:

New Zealand hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

(New Zealand series synchronous cylinder,produced by Hengyu Hydraulic Cylinder Factory）

series synchronous cylinder are widely used in New Zealand，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed series synchronous cylinder for customers from New Zealand.

Introduction to series synchronous cylinder:

When the piston speed of the series synchronous cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the series synchronous cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

When the series synchronous cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the series synchronous cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the series synchronous cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

What kind of process is used in the series synchronous cylinder to make high-quality series synchronous cylinder products: the body is the main component of the series synchronous cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The series synchronous cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the series synchronous cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the series synchronous cylinder increases by 25%. If the service life of the series synchronous cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. series synchronous cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the series synchronous cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and series synchronous cylinder are stuck or the series synchronous cylinder is blocked. At this time, no matter how to manipulate, the series synchronous cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the series synchronous cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about series synchronous cylinder:

Hydraulic cylinder performance requirements?
Hydraulic cylinder performance requirements: hydraulic cylinder is the hydraulic system to achieve energy transfer, conversion and control of the working medium, in addition, it is also responsible for the lubrication of the system, rust prevention, corrosion prevention and cooling. The performance of hydraulic oil will make the system flexible, accurate and reliable. Hydraulic performance requirements are determined according to the design parameters of the hydraulic system, operating conditions, the structure of the hydraulic pump and the working environment. Appropriate viscosity and good viscosion-temperature performance Viscosity is an important performance indicator of hydraulic pressure, which has an important impact on the smooth operation of the hydraulic system and the friction parts. The low temperature performance of hydraulic oil includes three aspects: low temperature flow, low temperature start-up and low temperature pumping.

Is a hydraulic cylinder and a jack the same thing?
Strictly speaking, no. Although the hydraulic principle is used, and even some of the longer jacks are similar to the cylinder, the internal structure of the two is different. There is a check valve inside the jack. After the top lift, the check valve locks the hydraulic oil circuit, and the hydraulic oil only enters and does not exit after the check valve locks, and can be lowered to complete a reciprocating movement. The cylinder is usually connected to the distribution tube to control the movement, and works with a wide variety of distribution valves and distribution systems according to different needs. The jack only needs a simple check valve.