swager cylinder Sold to Estonia

This article mainly introduces:

Estonia hydraulic cylinder,swager cylinder manufacturer,swager cylinder

(Estonia swager cylinder,produced by Hengyu Hydraulic Co., Ltd）

swager cylinder are widely used in Estonia，because of long service life，smooth movement，high work efficiency.So our company has designed swager cylinder for customers from Estonia.

Introduction to swager cylinder:

Piston swager cylinder is widely used in hydraulic transmission. When the swager cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the swager cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the swager cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

If the swager cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the swager cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow swager cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the swager cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the swager cylinder includes the leakage caused by excessive wear of the swager cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and swager cylinder, and the phenomenon of "pulling the swager cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

In order to ensure the service life of the swager cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

If the swager cylinder slips or crawls, please check whether there is astringency inside the swager cylinder, because the internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about swager cylinder:

Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

How does the variable amplitude cylinder work?
The variable amplitude cylinder is generally an engineering hydraulic cylinder connected by the front and back earrings, and the telescopic expansion of the hydraulic cylinder changes the Angle of the arm of the lifting machinery to achieve the role of the variable amplitude, according to the role it plays is called the variable amplitude cylinder, and there is no variable amplitude hydraulic cylinder in the classification of hydraulic cylinders.