rolling mill cylinder Sold to Romania

This article mainly introduces:

Romania hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

(Romania rolling mill cylinder,produced by Hengyu Hydraulic Co., Ltd）

rolling mill cylinder are widely used in Romania，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed rolling mill cylinder for customers from Romania.

Introduction to rolling mill cylinder:

In order to ensure the service life of the rolling mill cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the rolling mill cylinder, causing damage to the seal and causing leakage in the rolling mill cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

The rolling mill cylinder should be vented: when the rolling mill cylinder is installed or parked for a long time to work again, the air will penetrate into the rolling mill cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the rolling mill cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the rolling mill cylinder, the oil is best entered and discharged from the highest point of the rolling mill cylinder. rolling mill cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Most of the failure of the rolling mill cylinder is because there is a foreign body in the rolling mill cylinder into the failure of the rolling mill cylinder, the most problematic is that it is difficult to determine when the foreign body is into the rolling mill cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

The oil rolling mill cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about rolling mill cylinder:

What is the difference between hydraulic cylinder self-adjusting buffer and adjustable buffer?
If it is the buffer device inside the cylinder, then there are 4 basic forms, cylindrical buffer device, conical buffer device, variable throttle and adjustable flow groove. The biggest difference between the first three and the latter is that the latter can be adjusted through the external thimble to change the buffer strength, the first three mainly rely on the buffer device and buffer groove form to achieve the buffer (among them, the first type of buffer strength will not change, and the buffer strength of the two and three forms of buffer devices can be gradually increased).

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.