High quality hydraulic equipment manufacturers!
TELL:+8613184968882

lift cylinder of forklift truck Sold to Cameroon

Release time:2023-11-12 15:28:57 Hits: Current position: Home > News

This article mainly introduces:

Cameroon hydraulic cylinder,lift cylinder of forklift truck manufacturer,lift cylinder of forklift truck

Cameroon lift cylinder of forklift truck

(Cameroon lift cylinder of forklift truck,produced by Hebei Hengyu company)

lift cylinder of forklift truck are widely used in Cameroon,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed lift cylinder of forklift truck for customers from Cameroon.

Introduction to lift cylinder of forklift truck:

How to determine the working pressure of the lift cylinder of forklift truck: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, lift cylinder of forklift truck, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

When the lift cylinder of forklift truck is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the lift cylinder of forklift truck itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil lift cylinder of forklift truck should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical lift cylinder of forklift truck should use nitrile rubber dust ring; The filter device is added to the oil inlet of the lift cylinder of forklift truck of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

When the lift cylinder of forklift truck wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the lift cylinder of forklift truck inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the lift cylinder of forklift truck. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the lift cylinder of forklift truck can meet the requirements by grinding. However, the life and reliability of this repair lift cylinder of forklift truck are not high.

lift cylinder of forklift truck head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the lift cylinder of forklift truck head itself is the guide sleeve of the piston rod, the lift cylinder of forklift truck head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the lift cylinder of forklift truck head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Answers to some questions about lift cylinder of forklift truck:

The difference between the overall cylinder and the separate cylinder of the truck?
The whole cylinder is cast in one piece, and such a cylinder generally does not leak oil. Split cylinder refers to two welded, easy to leak oil in the welding place, resulting in damage to the cylinder, or its body can not get up, many people do not use this kind of cylinder now.

In a hydraulic system, a hydraulic pump has many hydraulic cylinders and hydraulic motors, and these executive components do not coordinate their actions with each other.
A load-sensitive variable pump can be used if these components sometimes need to work simultaneously and the power required is large. The required flow is distributed by the multi-way reversing valve, and the required flow and pressure changes are automatically adjusted by the hydraulic pump. Pressure reducing valves can be used for particularly low pressure circuits. Because you execute more components, the use of quantitative pump will cause a waste of energy, the system heat is large, not suitable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP