lifter hydraulic cylinder Sold to Saudi Arabia

This article mainly introduces:

Saudi Arabia hydraulic cylinder,lifter hydraulic cylinder manufacturer,lifter hydraulic cylinder

(Saudi Arabia lifter hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

lifter hydraulic cylinder are widely used in Saudi Arabia，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed lifter hydraulic cylinder for customers from Saudi Arabia.

Introduction to lifter hydraulic cylinder:

lifter hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the lifter hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When the hydraulic oil is not pumped into the lifter hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the lifter hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

lifter hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

In order to ensure the service life of the lifter hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

Answers to some questions about lifter hydraulic cylinder:

What is the material of the hydraulic cylinder slider?
Three parts of the hydraulic cylinder are essential, which are: cylinder - cylinder head assembly, piston - piston rod assembly, and sealing device. When you say slider, you mean piston. - Piston rod. Piston materials commonly used gray cast iron, wear-resistant cast iron, aluminum alloy (assembled), etc., can also be used 35 and 45 steel (integral). The piston rod is generally made of 35 and 45 steel. When the impact vibration is large, alloy steel such as 55 steel or 40Cr is used.

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.