servo hydraulic cylinder Sold to Norway

This article mainly introduces:

Norway hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

(Norway servo hydraulic cylinder,produced by Hebei Hengyu company）

servo hydraulic cylinder are widely used in Norway，because of high work efficiency，long service life，smooth movement.So our company has designed servo hydraulic cylinder for customers from Norway.

Introduction to servo hydraulic cylinder:

If the seal of the servo hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

servo hydraulic cylinder can not drive the load troubleshooting: oil pressure is too low. servo hydraulic cylinder selection specifications are too small. Leakage in servo hydraulic cylinder or associated hydraulic system element.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the servo hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The role of the servo hydraulic cylinder in the mold industry: the servo hydraulic cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the servo hydraulic cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The servo hydraulic cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

Answers to some questions about servo hydraulic cylinder:

How big is a 300-ton cylinder piston?
The rated pressure of the oil pump is 31.5 mpa, the nominal pressure of the hydraulic press is 3150 kN, then the calculated cross-sectional area of the cylinder: S=3150000/31500000=0.1 square meters diameter is: 2* root sign (0.1/3.14) =2*0.178 m =0.356 m 3150 kN hydraulic press is commonly equipped with 31.5 mpa 63 l/min axial piston pump. There are many variable forms of axial piston pump, and the motor size of the pump with the same flow and pressure is not uniform. 31.5 mpa 63 L/min automatic variable pump, can be equipped with 15 kW 4 stage motor; The manual variable pump needs to be equipped with 22 kW 4-stage motor.

What are the four cylinders of the truck crane?
The four cylinders of the truck crane generally refer to the telescopic cylinder of the boom (to adjust the length of the boom), the variable amplitude cylinder of the boom (to adjust the elevation Angle of the boom), the horizontal telescopic cylinder of the support leg and the vertical cylinder of the support leg.