road paving machine hydraulic cylinder Sold to Australia

This article mainly introduces:

Australia hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

(Australia road paving machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

road paving machine hydraulic cylinder are widely used in Australia，because of long service life，smooth movement，high work efficiency.So our company has designed road paving machine hydraulic cylinder for customers from Australia.

Introduction to road paving machine hydraulic cylinder:

road paving machine hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the road paving machine hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

If the road paving machine hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the road paving machine hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow road paving machine hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the road paving machine hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the road paving machine hydraulic cylinder includes the leakage caused by excessive wear of the road paving machine hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and road paving machine hydraulic cylinder, and the phenomenon of "pulling the road paving machine hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

road paving machine hydraulic cylinder and hydraulic station selection: Select the type and structure of the road paving machine hydraulic cylinder according to the operation requirements of the main engine. According to the external load force borne by the road paving machine hydraulic cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the road paving machine hydraulic cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the road paving machine hydraulic cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the road paving machine hydraulic cylinder, the diameter of the piston and the piston rod.

The machining accuracy of the road paving machine hydraulic cylinder depends on the level of equipment, production technology and testing means. road paving machine hydraulic cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

Answers to some questions about road paving machine hydraulic cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

What's a minus 40 cylinder made of?
Construction with 1Cr18Ni9Ti, in low temperature conditions impact and tensile strength are very good, can withstand -100 degrees of low temperature, corrosion resistance, material price is not very high, more economic.