road paving machine hydraulic cylinder Sold to Latvia

This article mainly introduces:

Latvia hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

(Latvia road paving machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

road paving machine hydraulic cylinder are widely used in Latvia，because of no need for deceleration device，excellent temperature resistance，no transmission clearance.So our company has designed road paving machine hydraulic cylinder for customers from Latvia.

Introduction to road paving machine hydraulic cylinder:

In recent years, the processing process of the road paving machine hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

In the case of serious wear on the inner surface of the road paving machine hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the road paving machine hydraulic cylinder manufacturing process for replacement. The road paving machine hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The road paving machine hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the road paving machine hydraulic cylinder, bite. Elimination method: When installing the road paving machine hydraulic cylinder, ensure that the axis position of the road paving machine hydraulic cylinder is consistent with the direction of movement; Make the load borne by the road paving machine hydraulic cylinder as far as possible through the road paving machine hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

The cavitation of the road paving machine hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the road paving machine hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Answers to some questions about road paving machine hydraulic cylinder:

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.

How does the cylinder of the shearing machine work?
Plate shear is a machine that cuts a sheet with a reciprocating straight motion from one blade to another. Through the moving upper blade and the fixed lower blade, the shear force is applied to the metal sheet of various thicknesses with a reasonable blade gap, so that the sheet is broken and separated according to the required size. Shearing machine belongs to one of the forging machinery, the main role is the metal processing industry. Products are widely used in aviation, light industry, metallurgy, chemical industry, construction, shipbuilding, automobile, electric power, electrical appliances, decoration and other industries to provide the required special machinery and complete sets of equipment. Working principle: The hydraulic system is used to drive the hydraulic cylinder to output a strong shear force to complete the shearing work.