push bench hydraulic cylinder Sold to Britain

This article mainly introduces:

Britain hydraulic cylinder,push bench hydraulic cylinder manufacturer,push bench hydraulic cylinder

(Britain push bench hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

push bench hydraulic cylinder are widely used in Britain，because of smooth movement，clever hydraulic energy conversion，powerful torque.So our company has designed push bench hydraulic cylinder for customers from Britain.

Introduction to push bench hydraulic cylinder:

When the push bench hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the push bench hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil push bench hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical push bench hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the push bench hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The "O" ring can be used as an auxiliary seal inside the push bench hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the push bench hydraulic cylinder, and can be completely sealed.

Factors that should be considered when selecting the oil seal in the push bench hydraulic cylinder: some specific factors should be taken into account when selecting the oil seal in the push bench hydraulic cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: push bench hydraulic cylinder diameter, piston rod diameter, piston rod and piston groove size, push bench hydraulic cylinder working pressure, push bench hydraulic cylinder movement speed, hydraulic system oil temperature and push bench hydraulic cylinder working environment.

push bench hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the push bench hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

Answers to some questions about push bench hydraulic cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.