steel mill cylinder Sold to Bolivia

This article mainly introduces:

Bolivia hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

(Bolivia steel mill cylinder,produced by Hengyu Hydraulic Cylinder Factory）

steel mill cylinder are widely used in Bolivia，because of high work efficiency，excellent temperature resistance，no transmission clearance.So our company has designed steel mill cylinder for customers from Bolivia.

Introduction to steel mill cylinder:

If the piston rod and steel mill cylinder are stuck or the steel mill cylinder is blocked, at this time, no matter how to operate, the steel mill cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steel mill cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

steel mill cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a steel mill cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' steel mill cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the steel mill cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The steel mill cylinder mainly outputs linear motion and force. The steel mill cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston steel mill cylinder, plunger steel mill cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger steel mill cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

steel mill cylinder is the most important part of construction machinery, the traditional processing method is: broaching steel mill cylinder block - fine boring steel mill cylinder block - grinding steel mill cylinder block. The rolling method is: broaching steel mill cylinder block - fine boring steel mill cylinder block - rolling steel mill cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the steel mill cylinder block is about 1-2 days, rolling 1 meter of the steel mill cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the steel mill cylinder increases by 25%. If the steel mill cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality steel mill cylinders, you must take the rolling production process. After the steel mill cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The repair method of steel mill cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about steel mill cylinder:

What is the rated pressure of the general cylinder?
This depends on the model of the cylinder, 1. The rated pressure of the light tie rod cylinder is 7 series 7MPa and 14 series 14MPa. 2. Rated pressure of engineering cylinder 16MPa. 3. Rexroth type metallurgical cylinder rated pressure 250MPa.

Loader arm fell badly, how to know which oil cylinder is leaking?
No matter which cylinder leakage the arm will drop, it is best to replace the oil seal, even if one cylinder is good, it will not last long, and it will drop the arm, so the two cylinders should be replaced at once.