hollow cylinder Sold to Tunisia

This article mainly introduces:

Tunisia hydraulic cylinder,hollow cylinder manufacturer,hollow cylinder

(Tunisia hollow cylinder,produced by Hengyu Group）

hollow cylinder are widely used in Tunisia，because of powerful torque，clever hydraulic energy conversion，no transmission clearance.So our company has designed hollow cylinder for customers from Tunisia.

Introduction to hollow cylinder:

If the hollow cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the hollow cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow hollow cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the hollow cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the hollow cylinder includes the leakage caused by excessive wear of the hollow cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and hollow cylinder, and the phenomenon of "pulling the hollow cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

We can not just consider the price and ignore the quality when we purchase the hollow cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the hollow cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the hollow cylinder is not required.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the hollow cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

hollow cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

Answers to some questions about hollow cylinder:

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.