Release time：2023-11-12 15:33:14 Hits： Current position: Home > News
This article mainly introduces:
Angola hydraulic cylinder,hydraulic punch cylinder manufacturer,hydraulic punch cylinder
(Angola hydraulic punch cylinder,produced by Hengyu Group）
hydraulic punch cylinder are widely used in Angola，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed hydraulic punch cylinder for customers from Angola.
The hydraulic punch cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure hydraulic punch cylinder can use 20 steel pipe, and the high pressure hydraulic punch cylinder can use 45 steel pipe.
If the hydraulic punch cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the hydraulic punch cylinder. The internal parts of the hydraulic punch cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the hydraulic punch cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the hydraulic punch cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the hydraulic punch cylinder bore processing is out of whack. Because the piston and hydraulic punch cylinder, guide rail and piston rod are relative If the hydraulic punch cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling hydraulic punch cylinder weight composition and calculation. The weight of the hydraulic punch cylinder is composed of the hydraulic punch cylinder diameter, the outer diameter and weight of the hydraulic punch cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.
The hydraulic punch cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.
How the cavitation of the hydraulic punch cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hydraulic punch cylinder, resulting in corrosive damage to the parts.
What is the valve on the hydraulic cylinder?
Oil valve, relief valve, overload valve, explosion-proof valve, etc., these are very convenient to insert! The oil valve, the overload valve and the blasting valve are very important for larger cylinders. Manufacturers will not offer you the selection. You need to choose the values by yourself according to your system, pump, cylinder, environment, working conditions and other comprehensive consideration!
How big is a 300-ton cylinder piston?
The rated pressure of the oil pump is 31.5 mpa, the nominal pressure of the hydraulic press is 3150 kN, then the calculated cross-sectional area of the cylinder: S=3150000/31500000=0.1 square meters diameter is: 2* root sign (0.1/3.14) =2*0.178 m =0.356 m 3150 kN hydraulic press is commonly equipped with 31.5 mpa 63 l/min axial piston pump. There are many variable forms of axial piston pump, and the motor size of the pump with the same flow and pressure is not uniform. 31.5 mpa 63 L/min automatic variable pump, can be equipped with 15 kW 4 stage motor; The manual variable pump needs to be equipped with 22 kW 4-stage motor.
Add Wechat