reset cylinder Sold to Indonesia

This article mainly introduces:

Indonesia hydraulic cylinder,reset cylinder manufacturer,reset cylinder

(Indonesia reset cylinder,produced by Hebei Hengyu company）

reset cylinder are widely used in Indonesia，because of simple structure and reliable operation，no need for deceleration device，excellent fatigue and impact resistance.So our company has designed reset cylinder for customers from Indonesia.

Introduction to reset cylinder:

reset cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a reset cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' reset cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the reset cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The reset cylinder mainly outputs linear motion and force. The reset cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston reset cylinder, plunger reset cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger reset cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The repair method of the reset cylinder: the repair of the reset cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

When the reset cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the reset cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the reset cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the reset cylinder can meet the requirements by grinding. However, the life and reliability of this repair reset cylinder are not high.

reset cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the reset cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

Answers to some questions about reset cylinder:

What is the difference between gas-hydraulic pressurized cylinder, pneumatic cylinder and oil cylinder?
The cylinder block is small and the force is large, constant speed and variable speed can be used (easy to change), the adjustment of the output is also convenient, and the freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Easy cylinder control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.