trunnion cylinder Sold to Bolivia

This article mainly introduces:

Bolivia hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

(Bolivia trunnion cylinder,produced by Hengyu Group）

trunnion cylinder are widely used in Bolivia，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Bolivia.

Introduction to trunnion cylinder:

The oil trunnion cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Piston trunnion cylinder is widely used in hydraulic transmission. When the trunnion cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the trunnion cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the trunnion cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

In recent years, the processing process of the trunnion cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

After chrome plating of the piston rod of the trunnion cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about trunnion cylinder:

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.