flange type cylinder Sold to Paraguay

This article mainly introduces:

Paraguay hydraulic cylinder,flange type cylinder manufacturer,flange type cylinder

(Paraguay flange type cylinder,produced by Hengyu Group）

flange type cylinder are widely used in Paraguay，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed flange type cylinder for customers from Paraguay.

Introduction to flange type cylinder:

If the flange type cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the flange type cylinder. The internal parts of the flange type cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the flange type cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the flange type cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the flange type cylinder bore processing is out of whack. Because the piston and flange type cylinder, guide rail and piston rod are relative If the flange type cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling flange type cylinder weight composition and calculation. The weight of the flange type cylinder is composed of the flange type cylinder diameter, the outer diameter and weight of the flange type cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

The machining accuracy of the flange type cylinder depends on the level of equipment, production technology and testing means. flange type cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

The viscosity of the working oil used in the flange type cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

flange type cylinder body inspection: The inner surface of the flange type cylinder and the piston seal are the main factors causing the leakage in the flange type cylinder, if the flange type cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the flange type cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about flange type cylinder:

How to select the propulsion cylinder according to the shield attitude, cylinder stroke, shield tail clearance and other factors?
Generally, the shield machine will be equipped with the corresponding cylinder. Soil pressure balancing machine, mud water balancing machine have the corresponding cylinder, there will be no insufficient cylinder force. In the jacking process of the pipe jacking machine, there are certain requirements for the jacking force of the cylinder.

What is the difference between single acting hydraulic cylinder and double acting hydraulic cylinder?
Single action hydraulic cylinder is a single direction force work, the return of the plunger depends on itself or the weight of the mechanism to return. The double acting hydraulic cylinder is mainly different from the extension and retraction of the piston (the thrust and tension of the saying), which are all operated by the action of liquid pressure.