hinge shaft cylinder Sold to Republic of Lithuania

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,hinge shaft cylinder manufacturer,hinge shaft cylinder

(Republic of Lithuania hinge shaft cylinder,produced by Hengyu Hydraulic Co., Ltd）

hinge shaft cylinder are widely used in Republic of Lithuania，because of no need for deceleration device，smooth movement，long service life.So our company has designed hinge shaft cylinder for customers from Republic of Lithuania.

Introduction to hinge shaft cylinder:

hinge shaft cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a hinge shaft cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' hinge shaft cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the hinge shaft cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The hinge shaft cylinder mainly outputs linear motion and force. The hinge shaft cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston hinge shaft cylinder, plunger hinge shaft cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger hinge shaft cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

hinge shaft cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

Before the hinge shaft cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the hinge shaft cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Answers to some questions about hinge shaft cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.