tension cylinder Sold to Switzerland

This article mainly introduces:

Switzerland hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Switzerland tension cylinder,produced by Hengyu Group）

tension cylinder are widely used in Switzerland，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed tension cylinder for customers from Switzerland.

Introduction to tension cylinder:

tension cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the tension cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

The role of the tension cylinder in the mold industry: the tension cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the tension cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The tension cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

When installing the tension cylinder pipe, the pipe should be cleaned after installation, and should not pass through the tension cylinder block, and the by-pass pipe must be installed in front of the oil port of the tension cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the tension cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the tension cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

When the tension cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the tension cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the tension cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about tension cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.