cylinder with sensor Sold to UAE

This article mainly introduces:

UAE hydraulic cylinder,cylinder with sensor manufacturer,cylinder with sensor

(UAE cylinder with sensor,produced by Hebei Hengyu company）

cylinder with sensor are widely used in UAE，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed cylinder with sensor for customers from UAE.

Introduction to cylinder with sensor:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the cylinder with sensor is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

How the cavitation of the cylinder with sensor is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the cylinder with sensor, resulting in corrosive damage to the parts.

The cylinder with sensor should be vented: when the cylinder with sensor is installed or parked for a long time to work again, the air will penetrate into the cylinder with sensor and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the cylinder with sensor and the system should be discharged. In order to facilitate the removal of air deposited in the cylinder with sensor, the oil is best entered and discharged from the highest point of the cylinder with sensor. cylinder with sensors that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

The coordination of the sliding parts of the cylinder with sensor itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

Answers to some questions about cylinder with sensor:

About the hydraulic cylinder wall thickness problem?
Hydraulic cylinder wall thickness calculation formula: t=PD/200St= pipe wall thickness (minimum thickness) mmP= maximum pressure kg/cm2? d= inner diameter mm? S=δ/5 safety factor δ= minimum tensile strength This case: set the cylinder material 45#, tensile strength 58kg/cm2t=(640X40)/(200X11.6)t=11mm piston output (i.e. Thrust) calculation formula: F1=PD2X(3.14/4)F1=640X42X0.785=8,038kg Note: Square numbers will not be used, all 2's in the text are square codes.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.