High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trailer hydraulic cylinder Sold to Italy

Release time:2023-11-08 08:12:01 Hits: Current position: Home > News

This article mainly introduces:

Italy hydraulic cylinder,trailer hydraulic cylinder manufacturer,trailer hydraulic cylinder

Italy trailer hydraulic cylinder

(Italy trailer hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trailer hydraulic cylinder are widely used in Italy,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed trailer hydraulic cylinder for customers from Italy.

Introduction to trailer hydraulic cylinder:

In the process of using the trailer hydraulic cylinder, sometimes such a problem will occur, the trailer hydraulic cylinder can not act immediately after the instruction of the trailer hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil trailer hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

There are some honeycomb holes in the inner wall of the trailer hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the trailer hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the trailer hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the trailer hydraulic cylinder is targeted to prevent. Is very necessary.

The quality of the trailer hydraulic cylinder can not be ignored in the purchase of the trailer hydraulic cylinder. The trailer hydraulic cylinder is the main component of the trailer hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. trailer hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of trailer hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

The trailer hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the trailer hydraulic cylinder should pay attention to: the operation should be as far away from the trailer hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the trailer hydraulic cylinder coating. When cleaning the trailer hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the trailer hydraulic cylinder when the oil temperature exceeds 70 ° C.

Answers to some questions about trailer hydraulic cylinder:

Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

How does the hydraulic solenoid valve realize that the cylinder stops at any position?
Use an O-type medium function solenoid directional valve, or use a Y-type solenoid directional valve and a hydraulically controlled check valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP