tension cylinder Sold to Thailand

This article mainly introduces:

Thailand hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Thailand tension cylinder,produced by Hengyu Group）

tension cylinder are widely used in Thailand，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed tension cylinder for customers from Thailand.

Introduction to tension cylinder:

The viscosity of the working oil used in the tension cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

What kind of process is used in the tension cylinder to make high-quality tension cylinder products: the body is the main component of the tension cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The tension cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the tension cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the tension cylinder increases by 25%. If the service life of the tension cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. tension cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the tension cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and tension cylinder are stuck or the tension cylinder is blocked. At this time, no matter how to manipulate, the tension cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the tension cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the initial action of the tension cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the tension cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

When producing oil tension cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

Answers to some questions about tension cylinder:

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).