cargo elevator hydraulic cylinder Sold to Malaysia

This article mainly introduces:

Malaysia hydraulic cylinder,cargo elevator hydraulic cylinder manufacturer,cargo elevator hydraulic cylinder

(Malaysia cargo elevator hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

cargo elevator hydraulic cylinder are widely used in Malaysia，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed cargo elevator hydraulic cylinder for customers from Malaysia.

Introduction to cargo elevator hydraulic cylinder:

The oil cargo elevator hydraulic cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

When the oil pressure of the cargo elevator hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

If the cargo elevator hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the cargo elevator hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow cargo elevator hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the cargo elevator hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the cargo elevator hydraulic cylinder includes the leakage caused by excessive wear of the cargo elevator hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and cargo elevator hydraulic cylinder, and the phenomenon of "pulling the cargo elevator hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the cargo elevator hydraulic cylinder is installed, the piston and the cargo elevator hydraulic cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the cargo elevator hydraulic cylinder head boss is easy to cause scars when it hits the inner surface of the cargo elevator hydraulic cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized cargo elevator hydraulic cylinders, only careful and careful operation can be avoided.

Answers to some questions about cargo elevator hydraulic cylinder:

How is the hydraulic cylinder selected in the mechanical design manual?
First of all, it is necessary to meet your work needs, and the second is to meet the structural space of the cylinder and accessories. Three to consider the other parameters of the cylinder.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.