High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Jordan

Release time:2023-11-19 14:06:21 Hits: Current position: Home > News

This article mainly introduces:

Jordan hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Jordan tailboard balance cylinder

(Jordan tailboard balance cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailboard balance cylinder are widely used in Jordan,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed tailboard balance cylinder for customers from Jordan.

Introduction to tailboard balance cylinder:

tailboard balance cylinder use should try to avoid sealing belt into the tailboard balance cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the tailboard balance cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the tailboard balance cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

In order to ensure the service life of the tailboard balance cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

The meaning of the tailboard balance cylinder model marked by the tailboard balance cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the tailboard balance cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the tailboard balance cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

When the tailboard balance cylinder needs to be stored for a period of time, please follow the recommended methods: The tailboard balance cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tailboard balance cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tailboard balance cylinder should not be in direct contact with water vapor for a long time. The tailboard balance cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tailboard balance cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tailboard balance cylinder Before working, the tailboard balance cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tailboard balance cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about tailboard balance cylinder:

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

What is the relationship between medium cylinder and side cylinder ratio of forklift truck?
The middle cylinder and the side cylinder seem to have no relationship, as long as the lifting speed required by the design can be ensured, but the diameter of the cylinder can not be too thin, so as to avoid the middle cylinder acting first when the high gantry vibration lifting, and then the two cylinders acting again.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP