steel mill cylinder Sold to Sweden

This article mainly introduces:

Sweden hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

(Sweden steel mill cylinder,produced by Hengyu Hydraulic Cylinder Factory）

steel mill cylinder are widely used in Sweden，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed steel mill cylinder for customers from Sweden.

Introduction to steel mill cylinder:

If the steel mill cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the steel mill cylinder. The internal parts of the steel mill cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the steel mill cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steel mill cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the steel mill cylinder bore processing is out of whack. Because the piston and steel mill cylinder, guide rail and piston rod are relative If the steel mill cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling steel mill cylinder weight composition and calculation. The weight of the steel mill cylinder is composed of the steel mill cylinder diameter, the outer diameter and weight of the steel mill cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

The definition of the minimum stable speed refers to the minimum movement speed of the steel mill cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the steel mill cylinder that undertakes different work has different requirements for the minimum stable speed.

When the steel mill cylinder is installed, the piston and the steel mill cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the steel mill cylinder head boss is easy to cause scars when it hits the inner surface of the steel mill cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized steel mill cylinders, only careful and careful operation can be avoided.

When installing the steel mill cylinder pipe, the pipe should be cleaned after installation, and should not pass through the steel mill cylinder block, and the by-pass pipe must be installed in front of the oil port of the steel mill cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the steel mill cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the steel mill cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about steel mill cylinder:

What are the reasons why the hydraulic cylinder action is slower than normal?
There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system under the pressure state is consistent with the initial setting. Before measuring the pressure, it is best to check the hydraulic oil and suction oil filter and replace or clean it. Second, check the main relief valve of the reversing control multiway valve to see if there is damage or foreign matter blocking, and clean it. If your pump is a gear pump, the problem should generally be small. Second, look at traffic. There is no leakage in the cylinder, leakage in the reversing valve spool and so on.

How to calculate multistage cylinder volume?
When the multi-stage cylinder is extended, the largest cylinder is extended first, and when the largest cylinder stroke is completed, the second largest cylinder is extended again, the second largest cylinder stroke is completed, the third largest cylinder is extended again... Therefore, the cylinder extension length is less than the stroke of the largest cylinder, and the volume is the extension length times the inner hole area of the largest cylinder. The cylinder extension length is greater than the maximum cylinder stroke and less than (the largest cylinder stroke + the second largest cylinder stroke), and the volume is the largest cylinder stroke times the internal hole area of the largest cylinder + (the extension length - the largest cylinder stroke) times the second largest cylinder.