steel mill cylinder Sold to Uruguay

This article mainly introduces:

Uruguay hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

(Uruguay steel mill cylinder,produced by Hengyu Hydraulic Cylinder Factory）

steel mill cylinder are widely used in Uruguay，because of smooth movement，long service life，powerful torque.So our company has designed steel mill cylinder for customers from Uruguay.

Introduction to steel mill cylinder:

In order to ensure the service life of the steel mill cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the steel mill cylinder, causing damage to the seal and causing leakage in the steel mill cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

If the seal of the steel mill cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

steel mill cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a steel mill cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' steel mill cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the steel mill cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The steel mill cylinder mainly outputs linear motion and force. The steel mill cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston steel mill cylinder, plunger steel mill cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger steel mill cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The assembly work of the steel mill cylinder has a great impact on the quality of the steel mill cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Answers to some questions about steel mill cylinder:

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.