stainless steel cylinder Sold to Algeria

This article mainly introduces:

Algeria hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Algeria stainless steel cylinder,produced by Hebei Hengyu company）

stainless steel cylinder are widely used in Algeria，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed stainless steel cylinder for customers from Algeria.

Introduction to stainless steel cylinder:

The stainless steel cylinder is mainly composed of body, piston, piston rod, stainless steel cylinder head, stainless steel cylinder bottom, piston rod head and related auxiliary devices. The piston divides the stainless steel cylinder into two chambers, and moves reciprocally in the stainless steel cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the stainless steel cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the stainless steel cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the stainless steel cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the stainless steel cylinder bottom and the stainless steel cylinder head is serious, so the buffer deceleration should be set at both ends of the stainless steel cylinder The working medium of the stainless steel cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; stainless steel cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the stainless steel cylinder: The buffer structure of the stainless steel cylinder is to prevent the piston from colliding with the stainless steel cylinder head at the end of the stroke.

What kind of process is used in the stainless steel cylinder to make high-quality stainless steel cylinder products: the body is the main component of the stainless steel cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The stainless steel cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the stainless steel cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stainless steel cylinder increases by 25%. If the service life of the stainless steel cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. stainless steel cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the stainless steel cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and stainless steel cylinder are stuck or the stainless steel cylinder is blocked. At this time, no matter how to manipulate, the stainless steel cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the stainless steel cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the stainless steel cylinder is in use, ensure that the stainless steel cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

When the initial action of the stainless steel cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the stainless steel cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about stainless steel cylinder:

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.