hydraulic shear cylinder Sold to Uruguay

This article mainly introduces:

Uruguay hydraulic cylinder,hydraulic shear cylinder manufacturer,hydraulic shear cylinder

(Uruguay hydraulic shear cylinder,produced by Hebei Hengyu company）

hydraulic shear cylinder are widely used in Uruguay，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed hydraulic shear cylinder for customers from Uruguay.

Introduction to hydraulic shear cylinder:

hydraulic shear cylinders in series, parallel and series parallel. Series: In the hydraulic shear cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the hydraulic shear cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the hydraulic shear cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the hydraulic shear cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

The repair method of hydraulic shear cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The hydraulic shear cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the hydraulic shear cylinder should pay attention to: the operation should be as far away from the hydraulic shear cylinder as possible, to avoid falling objects, knocking, rubbing the hydraulic shear cylinder coating. When cleaning the hydraulic shear cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the hydraulic shear cylinder when the oil temperature exceeds 70 ° C.

The hydraulic shear cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the hydraulic shear cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The hydraulic shear cylinder is basically composed of hydraulic shear cylinder and hydraulic shear cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

Answers to some questions about hydraulic shear cylinder:

Can multiple identical hydraulic cylinders be supplied with the same supply line?
This can be connected, but there is a disadvantage, that is, the hydraulic cylinder with the minimum pressure is extended first, and then the pressure is higher, and then the higher, until all the hydraulic cylinders are extended, which may not meet the requirements of field use.

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.