loading cylinder Sold to Estonia

This article mainly introduces:

Estonia hydraulic cylinder,loading cylinder manufacturer,loading cylinder

(Estonia loading cylinder,produced by Hebei Hengyu company）

loading cylinder are widely used in Estonia，because of no transmission clearance，clever hydraulic energy conversion，powerful torque.So our company has designed loading cylinder for customers from Estonia.

Introduction to loading cylinder:

loading cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a loading cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' loading cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the loading cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The loading cylinder mainly outputs linear motion and force. The loading cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston loading cylinder, plunger loading cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger loading cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

If the loading cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the loading cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The meaning of the loading cylinder model marked by the loading cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the loading cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the loading cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

Answers to some questions about loading cylinder:

How to calculate cylinder speed?
If there is a throttle valve, the cylinder speed will be adjustable. When the throttle is fully opened, the speed of the cylinder reaches the maximum: maximum speed = oil pump displacement ÷ cylinder cavity cross-sectional area The displacement of the oil pump is a main indicator, which can be found on the nameplate, and some can also be known by the oil pump model; The cross-sectional area of the cylinder cavity can be easily calculated. Just make sure the units are the same. And because the cross-sectional area of the rod cavity and the rodless cavity of the cylinder is different, the speed of advance and retreat may also be different.

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.