child hydraulic cylinder Sold to Australia

This article mainly introduces:

Australia hydraulic cylinder,child hydraulic cylinder manufacturer,child hydraulic cylinder

(Australia child hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

child hydraulic cylinder are widely used in Australia，because of long service life，smooth movement，high work efficiency.So our company has designed child hydraulic cylinder for customers from Australia.

Introduction to child hydraulic cylinder:

When the long-stroke child hydraulic cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in child hydraulic cylinder head seal damage, oil leakage, and piston sleep in the child hydraulic cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the child hydraulic cylinder; The piston and the piston rod are connected with a spherical joint.

If the child hydraulic cylinder slips or crawls, please check whether there is astringency inside the child hydraulic cylinder, because the internal parts of the child hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the child hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the child hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

child hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the child hydraulic cylinder head itself is the guide sleeve of the piston rod, the child hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the child hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

child hydraulic cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a child hydraulic cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' child hydraulic cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the child hydraulic cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The child hydraulic cylinder mainly outputs linear motion and force. The child hydraulic cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston child hydraulic cylinder, plunger child hydraulic cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger child hydraulic cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

Answers to some questions about child hydraulic cylinder:

Is it good or bad for the hydraulic cylinder working in the limit stroke position?
It is not good for the hydraulic cylinder working in the limit stroke position. Generally, when the cylinder is used in the limit stroke, the oil in the cylinder will form a backflow back pressure impact on the piston and guide sleeve seals. If the limit is not accurate, it is easy to cause collision damage. It is recommended to leave a buffer of ten to twenty centimeters.

How to set up the one-way cylinder hydraulic system?
Single acting oil cylinder, that is, an oil cylinder with an oil port, can use two three-way valves to control the cylinder action. The three oil ports are respectively connected to P (oil pump), A (oil cylinder), and T (oil tank). If the oil pump is to run continuously, an electromagnetic relief valve can be added. When the cylinder is not moving, the relief valve can unload the oil pump. You can also add a three-way four-way valve, the middle function is unloaded, two outlets: A connected to the fuel tank, B connected to the cylinder.