steering cylinder Sold to Argentina

This article mainly introduces:

Argentina hydraulic cylinder,steering cylinder manufacturer,steering cylinder

(Argentina steering cylinder,produced by Hengyu Hydraulic Co., Ltd）

steering cylinder are widely used in Argentina，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed steering cylinder for customers from Argentina.

Introduction to steering cylinder:

At the rated pressure, the thrust of the steering cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the steering cylinder is related to the diameter of the steering cylinder, but not to the stroke of the steering cylinder. Moreover, the larger the steering cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the steering cylinder.

steering cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a steering cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' steering cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the steering cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The steering cylinder mainly outputs linear motion and force. The steering cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston steering cylinder, plunger steering cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger steering cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

In the process of using the steering cylinder, sometimes such a problem will occur, the steering cylinder can not act immediately after the instruction of the steering cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil steering cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The steering cylinder can not be used as grounding electrode to avoid electric damage to the piston rod.

Answers to some questions about steering cylinder:

Do the collecting cylinder, distributing cylinder and distributing cylinder on the organic heat carrier boiler need to be notified separately as the pressure vessel for construction?
Do not need to be installed as a separate pressure vessel to inform, according to the organic heat carrier boiler can be informed. Write a "special equipment installation, renovation and maintenance notice" issued on it.

Is a hydraulic cylinder and a jack the same thing?
Strictly speaking, no. Although the hydraulic principle is used, and even some of the longer jacks are similar to the cylinder, the internal structure of the two is different. There is a check valve inside the jack. After the top lift, the check valve locks the hydraulic oil circuit, and the hydraulic oil only enters and does not exit after the check valve locks, and can be lowered to complete a reciprocating movement. The cylinder is usually connected to the distribution tube to control the movement, and works with a wide variety of distribution valves and distribution systems according to different needs. The jack only needs a simple check valve.