Release time：2023-11-27 15:08:48 Hits： Current position: Home > News
This article mainly introduces:
El Salvador hydraulic cylinder,roller press hydraulic cylinder manufacturer,roller press hydraulic cylinder
(El Salvador roller press hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）
roller press hydraulic cylinder are widely used in El Salvador，because of long service life，high work efficiency，no transmission clearance.So our company has designed roller press hydraulic cylinder for customers from El Salvador.
The coordination of the sliding parts of the roller press hydraulic cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.
Causes and countermeasures of oil roller press hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the roller press hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the roller press hydraulic cylinder is visibly scarred, the roller press hydraulic cylinder must be replaced. It can be pressurized at one end of the roller press hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most roller press hydraulic cylinder piston drift may not come from the roller press hydraulic cylinder, the above method to determine the roller press hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.
When the roller press hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the roller press hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.
The method of sleeve roller press hydraulic cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the roller press hydraulic cylinder can be significantly improved by rolling in the finishing of the inner holes of the roller press hydraulic cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.
How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.
What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.
Add Wechat