double acting cylinder Sold to Australia

This article mainly introduces:

Australia hydraulic cylinder,double acting cylinder manufacturer,double acting cylinder

(Australia double acting cylinder,produced by Hengyu Hydraulic Cylinder Factory）

double acting cylinder are widely used in Australia，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed double acting cylinder for customers from Australia.

Introduction to double acting cylinder:

If the double acting cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the double acting cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow double acting cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the double acting cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the double acting cylinder includes the leakage caused by excessive wear of the double acting cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and double acting cylinder, and the phenomenon of "pulling the double acting cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

double acting cylinder can not drive the load troubleshooting: oil pressure is too low. double acting cylinder selection specifications are too small. Leakage in double acting cylinder or associated hydraulic system element.

When the control pressure of the hydraulic system is too low, the double acting cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The coordination of the sliding parts of the double acting cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

Answers to some questions about double acting cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.