stern plate hydraulic cylinder Sold to New Zealand

This article mainly introduces:

New Zealand hydraulic cylinder,stern plate hydraulic cylinder manufacturer,stern plate hydraulic cylinder

(New Zealand stern plate hydraulic cylinder,produced by Hebei Hengyu company）

stern plate hydraulic cylinder are widely used in New Zealand，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stern plate hydraulic cylinder for customers from New Zealand.

Introduction to stern plate hydraulic cylinder:

The stern plate hydraulic cylinder should be vented: when the stern plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the stern plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the stern plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the stern plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the stern plate hydraulic cylinder. stern plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

If the stern plate hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the stern plate hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow stern plate hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the stern plate hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the stern plate hydraulic cylinder includes the leakage caused by excessive wear of the stern plate hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and stern plate hydraulic cylinder, and the phenomenon of "pulling the stern plate hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Before purchasing the stern plate hydraulic cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

The stern plate hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure stern plate hydraulic cylinder can use 20 steel pipe, and the high pressure stern plate hydraulic cylinder can use 45 steel pipe.

Answers to some questions about stern plate hydraulic cylinder:

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.

What is a variable amplitude cylinder?
The type of variable amplitude cylinder is: double acting piston type cylinder, single acting plunger type cylinder, double acting two-stage telescopic cylinder. Double acting piston cylinder is the most common application. The oil cylinder has two oil outlets, and when the oil is fed into the A port, the oil is returned to the B port; If the oil inlet of the B port is returned to the oil of the A port, the reciprocating movement of the piston depends on the effect of pressure. Single-acting plunger (or piston) cylinder has only one oil port, the pressure oil can only supply oil to one side of the plunger in the cylinder, the plunger moves in one direction under the action of pressure oil, and the return stroke of the plunger is driven by the gravity of the lifting arm, such as the LT1040 truck crane variable amplitude cylinder. The double-acting two-stage telescopic cylinder is a set structure, and the two-stage piston rod is like a tie rod antenna set in the cylinder barrel.