garbage truck hydraulic cylinder Sold to Guatemala

This article mainly introduces:

Guatemala hydraulic cylinder,garbage truck hydraulic cylinder manufacturer,garbage truck hydraulic cylinder

(Guatemala garbage truck hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

garbage truck hydraulic cylinder are widely used in Guatemala，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed garbage truck hydraulic cylinder for customers from Guatemala.

Introduction to garbage truck hydraulic cylinder:

The piston rod of the garbage truck hydraulic cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

What kind of process is used in the garbage truck hydraulic cylinder to make high-quality garbage truck hydraulic cylinder products: the body is the main component of the garbage truck hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The garbage truck hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the garbage truck hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the garbage truck hydraulic cylinder increases by 25%. If the service life of the garbage truck hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. garbage truck hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the garbage truck hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and garbage truck hydraulic cylinder are stuck or the garbage truck hydraulic cylinder is blocked. At this time, no matter how to manipulate, the garbage truck hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the garbage truck hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the garbage truck hydraulic cylinder is installed, the piston and the garbage truck hydraulic cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the garbage truck hydraulic cylinder head boss is easy to cause scars when it hits the inner surface of the garbage truck hydraulic cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized garbage truck hydraulic cylinders, only careful and careful operation can be avoided.

When producing oil garbage truck hydraulic cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

Answers to some questions about garbage truck hydraulic cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar