unidirectional cylinder Sold to Burma

This article mainly introduces:

Burma hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

(Burma unidirectional cylinder,produced by Hengyu Group）

unidirectional cylinder are widely used in Burma，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed unidirectional cylinder for customers from Burma.

Introduction to unidirectional cylinder:

The unidirectional cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure unidirectional cylinder can use 20 steel pipe, and the high pressure unidirectional cylinder can use 45 steel pipe.

The material of the sliding part of the unidirectional cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

What kind of process is used in the unidirectional cylinder to make high-quality unidirectional cylinder products: the body is the main component of the unidirectional cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The unidirectional cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the unidirectional cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the unidirectional cylinder increases by 25%. If the service life of the unidirectional cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. unidirectional cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the unidirectional cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and unidirectional cylinder are stuck or the unidirectional cylinder is blocked. At this time, no matter how to manipulate, the unidirectional cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the unidirectional cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The main role of the unidirectional cylinder: the unidirectional cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the unidirectional cylinder realizes reciprocating motion. The structure of the unidirectional cylinder has three categories: piston unidirectional cylinder, plunger unidirectional cylinder, swing unidirectional cylinder, piston unidirectional cylinder and plunger unidirectional cylinder to achieve reciprocating linear motion, output speed and thrust, swing unidirectional cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the unidirectional cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The unidirectional cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

Answers to some questions about unidirectional cylinder:

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

What is a hydraulic cylinder assembly?
Assembly, which means aggregate. A series of parts or products, formed to achieve a specific function of the whole, the general term for this system is assembly. The hydraulic cylinder assembly is not a single hydraulic cylinder part, which can be used by connecting the hydraulic hose.