tilting furnace hydraulic cylinder Sold to Dominica

This article mainly introduces:

Dominica hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Dominica tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

tilting furnace hydraulic cylinder are widely used in Dominica，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed tilting furnace hydraulic cylinder for customers from Dominica.

Introduction to tilting furnace hydraulic cylinder:

tilting furnace hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer tilting furnace hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

When the initial action of the tilting furnace hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the tilting furnace hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

The tilting furnace hydraulic cylinder should be used correctly and maintained regularly. The tilting furnace hydraulic cylinder should be deflated before use, the buffer regulating valve should be adjusted to a reasonable position, the cleanliness of the oil should be checked regularly, the dust on the tilting furnace hydraulic cylinder should be cleaned regularly, and attention should be paid to waterproof and fireproof.

tilting furnace hydraulic cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a tilting furnace hydraulic cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' tilting furnace hydraulic cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the tilting furnace hydraulic cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The tilting furnace hydraulic cylinder mainly outputs linear motion and force. The tilting furnace hydraulic cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston tilting furnace hydraulic cylinder, plunger tilting furnace hydraulic cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger tilting furnace hydraulic cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

Answers to some questions about tilting furnace hydraulic cylinder:

A hydraulic system functions three cylinders to maintain pressure, what components need to be used?
Two way cartridge valve can be selected for control. Two way cartridge valve advantages: 1) flow capacity is large, especially suitable for large flow occasions. 2) The spool has sensitive action and strong anti-clogging ability. 3) Good sealing, small leakage, oil flow through the valve pressure loss is small. 4) Simple structure, easy to standardize.

What is the function of the hinged cylinder of the shield machine?
The articulated cylinder is used for the shield when the radius of curvature is very small during the propulsion process, that is, for turning. For example, a propulsion section with a radius of curvature of R150 can only be turned using an articulated system due to the sensitivity of the shield body (i.e. the length of the shield body divided by its outside diameter). However, in the construction process, the use of articulated systems is not much.