trunnion cylinder Sold to America

This article mainly introduces:

America hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

(America trunnion cylinder,produced by Hengyu Group）

trunnion cylinder are widely used in America，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from America.

Introduction to trunnion cylinder:

When the trunnion cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the trunnion cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the trunnion cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

If it is found that the trunnion cylinder lubrication is poor or the trunnion cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the trunnion cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the trunnion cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the trunnion cylinder center line. In this way, when the piston works in the trunnion cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the trunnion cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

trunnion cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a trunnion cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' trunnion cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the trunnion cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The trunnion cylinder mainly outputs linear motion and force. The trunnion cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston trunnion cylinder, plunger trunnion cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger trunnion cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

When the trunnion cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the trunnion cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

Answers to some questions about trunnion cylinder:

What valve is used to control the speed of the cylinder?
Hydraulic cylinder for lifting is generally the piston rod downward installation, to achieve the fast and slow speed of the cylinder, you can add a two-digit three-way electromagnetic reversing valve + a throttle valve on a branch at the bottom of the cylinder, you can achieve speed change, control mode can be controlled by time control can also be controlled by stroke switch. If you want to achieve more accurate control can use proportional valve control.

What is hydraulic cylinder internal leakage and external leakage?
The internal leakage of the hydraulic cylinder refers to the leakage of the piston head seal of the double-acting cylinder, and the leakage occurs inside the cylinder; The external leakage refers to the leakage phenomenon between the cylinder head (or cylinder guide sleeve) and the plunger rod (or piston rod) and the seal between the guide sleeve and the cylinder block, and the oil in the hydraulic cylinder leaks to the outside.