High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Mexico

Release time:2023-11-09 08:46:31 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

Mexico vehicle hydraulic cylinder

(Mexico vehicle hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

vehicle hydraulic cylinder are widely used in Mexico,because of no need for deceleration device,smooth movement,long service life.So our company has designed vehicle hydraulic cylinder for customers from Mexico.

Introduction to vehicle hydraulic cylinder:

Causes and countermeasures of oil vehicle hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the vehicle hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the vehicle hydraulic cylinder is visibly scarred, the vehicle hydraulic cylinder must be replaced. It can be pressurized at one end of the vehicle hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most vehicle hydraulic cylinder piston drift may not come from the vehicle hydraulic cylinder, the above method to determine the vehicle hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

The piston rod and guide sleeve function of the vehicle hydraulic cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

The meaning of the vehicle hydraulic cylinder model marked by the vehicle hydraulic cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the vehicle hydraulic cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the vehicle hydraulic cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

vehicle hydraulic cylinders in series, parallel and series parallel. Series: In the vehicle hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the vehicle hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the vehicle hydraulic cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the vehicle hydraulic cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about vehicle hydraulic cylinder:

Why is the cylinder not in place when the concrete pump truck changes the piston?
When the concrete pump truck changes the piston, the cylinder is not in place mainly because the transfer oil connecting the two cylinders is not completely drained. Sany and Zhonglian have a piston return switch, which can be used to back the piston to the cleaning tank. The elephant is equipped with a stop valve at the bottom of the oil cylinder, usually in the closed state, when opened, the piston can be returned to the cleaning tank, remember to close the valve after the piston is updated.

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP