tension cylinder Sold to Austria

This article mainly introduces:

Austria hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Austria tension cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tension cylinder are widely used in Austria，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed tension cylinder for customers from Austria.

Introduction to tension cylinder:

tension cylinder can not drive the load troubleshooting: oil pressure is too low. tension cylinder selection specifications are too small. Leakage in tension cylinder or associated hydraulic system element.

The internal leakage of the tension cylinder should be prevented when the tension cylinder is used. The internal leakage of tension cylinder includes the leakage caused by excessive wear of tension cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The oil tension cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the tension cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the tension cylinder. The internal parts of the tension cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the tension cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tension cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the tension cylinder bore processing is out of whack. Because the piston and tension cylinder, guide rail and piston rod are relative If the tension cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling tension cylinder weight composition and calculation. The weight of the tension cylinder is composed of the tension cylinder diameter, the outer diameter and weight of the tension cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Answers to some questions about tension cylinder:

How does the cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, the executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, the control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, the auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

The two cylinders of the bending machine are out of sync?
Check whether the sliding slide is worn, adjust its tightness, so that both sides are consistent, check whether the two cylinder tubing is connected, tighten the flow valve, pressure, let the cylinder air discharge.