unidirectional cylinder Sold to Qatar

This article mainly introduces:

Qatar hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

(Qatar unidirectional cylinder,produced by Hengyu Hydraulic Cylinder Factory）

unidirectional cylinder are widely used in Qatar，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed unidirectional cylinder for customers from Qatar.

Introduction to unidirectional cylinder:

The meaning of the unidirectional cylinder model marked by the unidirectional cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the unidirectional cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the unidirectional cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

When the unidirectional cylinder needs to be stored for a period of time, please follow the recommended methods: The unidirectional cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the unidirectional cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil unidirectional cylinder should not be in direct contact with water vapor for a long time. The unidirectional cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the unidirectional cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the unidirectional cylinder Before working, the unidirectional cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the unidirectional cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Improve the service life of the unidirectional cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the unidirectional cylinder (such as the unidirectional cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the unidirectional cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the unidirectional cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single unidirectional cylinder exhaust.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about unidirectional cylinder:

When there is only one hole in the oil inlet and outlet of the hydraulic cylinder, will there be oil leakage?
It is a single acting oil cylinder. This oil cylinder is always driven by hydraulic oil in advance, and is generally pulled back by the spring at the bottom of the piston or the weight of the cylinder piston or the load. But either way, it has nothing to do with any internal leakage. Whether the oil is internally drained is related to the sealing and accuracy of the cylinder itself.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.