unidirectional cylinder Sold to Spain

This article mainly introduces:

Spain hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

(Spain unidirectional cylinder,produced by Hengyu Group）

unidirectional cylinder are widely used in Spain，because of excellent fatigue and impact resistance，smooth movement，high work efficiency.So our company has designed unidirectional cylinder for customers from Spain.

Introduction to unidirectional cylinder:

If the unidirectional cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the unidirectional cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow unidirectional cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the unidirectional cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the unidirectional cylinder includes the leakage caused by excessive wear of the unidirectional cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and unidirectional cylinder, and the phenomenon of "pulling the unidirectional cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the unidirectional cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the unidirectional cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

After the unidirectional cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

When the unidirectional cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the unidirectional cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the unidirectional cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about unidirectional cylinder:

Why does the hydraulic cylinder rebound after the rod cavity is extended into place?
The reason is that after the rod cavity is extended into place, the rod cavity and the rodless cavity are connected, so that the cylinder moves towards the rod cavity. After connecting, it is equivalent to the hydraulic oil directly driving the cylinder with an area equal to the piston rod. After the end of this problem, it is estimated that the seal is not very good, and the two cavities are connected after the pressure is increased to a certain extent; Or there is a problem in the valve, so that the two chambers are connected after reaching a certain pressure. Other phenomena: If the load is increased to a certain extent, no matter which side of the solenoid valve is energized, the cylinder will move to the rod cavity.

What is the smallest cylinder size?
The smallest shape cylinder I have ever seen is a hydraulic clamping cylinder in the machine tool industry. Outer diameter 24 mm, total length 23 mm, travel 4 mm. Weighs 0.05 kg. Maximum clamping force 3500 Newtons.