trunnion cylinder Sold to Germany

This article mainly introduces:

Germany hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

(Germany trunnion cylinder,produced by Hengyu Hydraulic Co., Ltd）

trunnion cylinder are widely used in Germany，because of no need for deceleration device，long service life，smooth movement.So our company has designed trunnion cylinder for customers from Germany.

Introduction to trunnion cylinder:

When using the trunnion cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the trunnion cylinder block. If the trunnion cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the trunnion cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the trunnion cylinder, so that the working efficiency of the trunnion cylinder is reduced.

If the trunnion cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the trunnion cylinder. The internal parts of the trunnion cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the trunnion cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the trunnion cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the trunnion cylinder bore processing is out of whack. Because the piston and trunnion cylinder, guide rail and piston rod are relative If the trunnion cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling trunnion cylinder weight composition and calculation. The weight of the trunnion cylinder is composed of the trunnion cylinder diameter, the outer diameter and weight of the trunnion cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

When the oil pressure of the trunnion cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

If air enters the hydraulic system, the trunnion cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

Answers to some questions about trunnion cylinder:

What is the smallest cylinder size?
The smallest shape cylinder I have ever seen is a hydraulic clamping cylinder in the machine tool industry. Outer diameter 24 mm, total length 23 mm, travel 4 mm. Weighs 0.05 kg. Maximum clamping force 3500 Newtons.

How to distinguish the size of hydraulic cylinder cavity?
The hydraulic cylinder has a rod cavity and a rodless cavity. The rod cavity is the cavity that the piston rod extends out. The rod cavity is of course small due to the existence of the piston rod. That's just relative.