differential cylinder Sold to UAE

This article mainly introduces:

UAE hydraulic cylinder,differential cylinder manufacturer,differential cylinder

(UAE differential cylinder,produced by Hengyu Hydraulic Cylinder Factory）

differential cylinder are widely used in UAE，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed differential cylinder for customers from UAE.

Introduction to differential cylinder:

If the differential cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the differential cylinder. The internal parts of the differential cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the differential cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the differential cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the differential cylinder bore processing is out of whack. Because the piston and differential cylinder, guide rail and piston rod are relative If the differential cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling differential cylinder weight composition and calculation. The weight of the differential cylinder is composed of the differential cylinder diameter, the outer diameter and weight of the differential cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

differential cylinder installation precautions: Before installing the differential cylinder into the system, the parameters on the differential cylinder label should be compared with the parameters when ordering. The base of the differential cylinder must have sufficient stiffness, otherwise the differential cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

In the process of using the differential cylinder, sometimes such a problem will occur, the differential cylinder can not act immediately after the instruction of the differential cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil differential cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When the control pressure of the hydraulic system is too low, the differential cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about differential cylinder:

How to calculate the cross-sectional area of hydraulic cylinder?
Hydraulic cylinder cross section integral rod cavity and rodless cavity: rod cavity is cylinder inner wall cross-sectional area - piston rod cross-sectional area; The rodless cavity is the cross-sectional area of the inner wall of the cylinder. If the working pressure p and the output force F are known, the effective cross-sectional area A=F/p can be calculated.

What are the main technical parameters of the hydraulic cylinder?
Parameters are as follows: 1, cylinder diameter, inner diameter size; 2, import and export diameter and thread parameters; 3, piston rod diameter; 4, cylinder pressure, cylinder working pressure, calculation is often used test pressure, less than 16MPa multiplied by 1.5, higher than 16MPa multiplied by 1.25. 5, cylinder stroke; 6. Is there a buffer? According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7, the installation of the cylinder.