hoister hydraulic cylinder(hoister hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）hoister hydraulic cylinder are widely used ，because of no need for deceleration device，long se
(hoister hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）
hoister hydraulic cylinder are widely used ，because of no need for deceleration device，long service life，smooth movement.So our company has designed hoister hydraulic cylinder for our customers.
If the hoister hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.
hoister hydraulic cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards hoister hydraulic cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the hoister hydraulic cylinder guide is determined by the length of the stroke. Check the strength of hoister hydraulic cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.
hoister hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching hoister hydraulic cylinder block - fine boring hoister hydraulic cylinder block - grinding hoister hydraulic cylinder block. The rolling method is: broaching hoister hydraulic cylinder block - fine boring hoister hydraulic cylinder block - rolling hoister hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the hoister hydraulic cylinder block is about 1-2 days, rolling 1 meter of the hoister hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the hoister hydraulic cylinder increases by 25%. If the hoister hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality hoister hydraulic cylinders, you must take the rolling production process. After the hoister hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.
When the hoister hydraulic cylinder is in use, ensure that the hoister hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.
What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.
What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.
Add Wechat