tilting furnace hydraulic cylinder Sold to El Salvador

This article mainly introduces:

El Salvador hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(El Salvador tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tilting furnace hydraulic cylinder are widely used in El Salvador，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed tilting furnace hydraulic cylinder for customers from El Salvador.

Introduction to tilting furnace hydraulic cylinder:

The tilting furnace hydraulic cylinder should be vented: when the tilting furnace hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the tilting furnace hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the tilting furnace hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the tilting furnace hydraulic cylinder, the oil is best entered and discharged from the highest point of the tilting furnace hydraulic cylinder. tilting furnace hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

The tilting furnace hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

When the tilting furnace hydraulic cylinder is installed, the piston and the tilting furnace hydraulic cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the tilting furnace hydraulic cylinder head boss is easy to cause scars when it hits the inner surface of the tilting furnace hydraulic cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized tilting furnace hydraulic cylinders, only careful and careful operation can be avoided.

The main role of the tilting furnace hydraulic cylinder: the tilting furnace hydraulic cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the tilting furnace hydraulic cylinder realizes reciprocating motion. The structure of the tilting furnace hydraulic cylinder has three categories: piston tilting furnace hydraulic cylinder, plunger tilting furnace hydraulic cylinder, swing tilting furnace hydraulic cylinder, piston tilting furnace hydraulic cylinder and plunger tilting furnace hydraulic cylinder to achieve reciprocating linear motion, output speed and thrust, swing tilting furnace hydraulic cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the tilting furnace hydraulic cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The tilting furnace hydraulic cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

Answers to some questions about tilting furnace hydraulic cylinder:

How to distinguish high pressure cylinder and low pressure cylinder?
There is no special definition of the cylinder, the so-called pressure classification refers to the pump low pressure (code L) container 0.1MPa ≤p < 1.6MPa; Medium pressure (code M) container 1.6MPa ≤p < 10.0MPa; High pressure (code H) vessel 10 MPa≤p < 100 MPa; Ultra-high pressure (code U) container p≥100MPa. (1MPa=9.8Kg)

When does the cylinder rotate?
The piston rod inside the multistage plunger cylinder can be rotated, and it will rotate when it is subjected to tangential force.