yg series hydraulic cylinder Sold to Bahrain

This article mainly introduces:

Bahrain hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Bahrain yg series hydraulic cylinder,produced by Hengyu Group）

yg series hydraulic cylinder are widely used in Bahrain，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from Bahrain.

Introduction to yg series hydraulic cylinder:

There are some honeycomb holes in the inner wall of the yg series hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the yg series hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the yg series hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the yg series hydraulic cylinder is targeted to prevent. Is very necessary.

If the yg series hydraulic cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the yg series hydraulic cylinder. The internal parts of the yg series hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the yg series hydraulic cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the yg series hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the yg series hydraulic cylinder bore processing is out of whack. Because the piston and yg series hydraulic cylinder, guide rail and piston rod are relative If the yg series hydraulic cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling yg series hydraulic cylinder weight composition and calculation. The weight of the yg series hydraulic cylinder is composed of the yg series hydraulic cylinder diameter, the outer diameter and weight of the yg series hydraulic cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

yg series hydraulic cylinder use should try to avoid sealing belt into the yg series hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the yg series hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the yg series hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

After chrome plating of the piston rod of the yg series hydraulic cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about yg series hydraulic cylinder:

How to exhaust hydraulic cylinder?
Exhaust: The hydraulic system generally does not have exhaust, the use of the tank can exhaust, the oil operation will bring the gas back to the tank, and the tank can be communicated with the atmosphere. The gas will escape from the oil.

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.