supporting cylinder Sold to Brazil

This article mainly introduces:

Brazil hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

(Brazil supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory）

supporting cylinder are widely used in Brazil，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed supporting cylinder for customers from Brazil.

Introduction to supporting cylinder:

If the supporting cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the supporting cylinder. The internal parts of the supporting cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the supporting cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the supporting cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the supporting cylinder bore processing is out of whack. Because the piston and supporting cylinder, guide rail and piston rod are relative If the supporting cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling supporting cylinder weight composition and calculation. The weight of the supporting cylinder is composed of the supporting cylinder diameter, the outer diameter and weight of the supporting cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

The repair method of supporting cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

supporting cylinder is the most important part of construction machinery, the traditional processing method is: broaching supporting cylinder block - fine boring supporting cylinder block - grinding supporting cylinder block. The rolling method is: broaching supporting cylinder block - fine boring supporting cylinder block - rolling supporting cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the supporting cylinder block is about 1-2 days, rolling 1 meter of the supporting cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the supporting cylinder increases by 25%. If the supporting cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality supporting cylinders, you must take the rolling production process. After the supporting cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

When the supporting cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the supporting cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the supporting cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the supporting cylinder can meet the requirements by grinding. However, the life and reliability of this repair supporting cylinder are not high.

Answers to some questions about supporting cylinder:

What hydraulic valve is used to control a cylinder back and forth?
Direction valve is available. Direction valve includes electromagnetic directional valve, manual directional valve, check valve, hydraulic control check valve, the specific choice of which direction valve, you need to see the use of conditions.

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.