stroke adjustable cylinder Sold to Colombia

This article mainly introduces:

Colombia hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

(Colombia stroke adjustable cylinder,produced by Hengyu Hydraulic Cylinder Factory）

stroke adjustable cylinder are widely used in Colombia，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed stroke adjustable cylinder for customers from Colombia.

Introduction to stroke adjustable cylinder:

stroke adjustable cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When the stroke adjustable cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the stroke adjustable cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil stroke adjustable cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical stroke adjustable cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the stroke adjustable cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The cavitation of the stroke adjustable cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the stroke adjustable cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

If air enters the hydraulic system, the stroke adjustable cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

Answers to some questions about stroke adjustable cylinder:

What parameters do I need to provide when purchasing hydraulic cylinders?
The main technical parameters of the hydraulic cylinder: 1. Cylinder diameter; Cylinder diameter, inner diameter size; 2. Piston rod diameter; 3. Cylinder stroke; 4. Cylinder pressure; The working pressure of the cylinder is often calculated using the test pressure, which is less than 16MPa multiplied by 1.5 and higher than 16 multiplied by 1.255. Import and export diameter and thread parameters; 6. Whether there is buffer; According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7. Installation method of oil cylinder, etc.

Loader arm fell badly, how to know which oil cylinder is leaking?
No matter which cylinder leakage the arm will drop, it is best to replace the oil seal, even if one cylinder is good, it will not last long, and it will drop the arm, so the two cylinders should be replaced at once.