hinge shaft cylinder Sold to Pakistan

This article mainly introduces:

Pakistan hydraulic cylinder,hinge shaft cylinder manufacturer,hinge shaft cylinder

(Pakistan hinge shaft cylinder,produced by Hengyu Hydraulic Co., Ltd）

hinge shaft cylinder are widely used in Pakistan，because of long service life，smooth movement，high work efficiency.So our company has designed hinge shaft cylinder for customers from Pakistan.

Introduction to hinge shaft cylinder:

hinge shaft cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a hinge shaft cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' hinge shaft cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the hinge shaft cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The hinge shaft cylinder mainly outputs linear motion and force. The hinge shaft cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston hinge shaft cylinder, plunger hinge shaft cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger hinge shaft cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The hinge shaft cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the hinge shaft cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The hinge shaft cylinder is basically composed of hinge shaft cylinder and hinge shaft cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

What kind of process is used in the hinge shaft cylinder to make high-quality hinge shaft cylinder products: the body is the main component of the hinge shaft cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The hinge shaft cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the hinge shaft cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the hinge shaft cylinder increases by 25%. If the service life of the hinge shaft cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. hinge shaft cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hinge shaft cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and hinge shaft cylinder are stuck or the hinge shaft cylinder is blocked. At this time, no matter how to manipulate, the hinge shaft cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the hinge shaft cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

If air enters the hydraulic system, the hinge shaft cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

Answers to some questions about hinge shaft cylinder:

The pressure gauge of the hydraulic station reaches 20MPa. How many tons of weight can the hydraulic cylinder lift? How to convert?
20Mpa=200kg/cm^2 The weight of the cylinder with a cross-sectional area of 1 square centimeter can be lifted is 200kg, so F=200X3.14X (125/2) ^2 =24531kg =24.5 tons.

Hydraulic cylinder application areas?
1, in the machine tool industry, 85% of the machine tool transmission system adopts hydraulic transmission and control. Such as grinding machine, milling machine, planer, broaching machine, press, shearing machine, and combined machine tools. 2, in the metallurgical industry, electric furnace control system, rolling mill control system, open furnace charging, converter control, blast furnace control, strip deviation and constant tension device are all using hydraulic cylinders. 3, in the construction machinery, the general use of hydraulic transmission, such as excavators, tire loaders, truck cranes, crawler bulldozers, tire cranes, self-propelled scrapers, graders and vibration rollers. 4, in agricultural machinery, the use of hydraulic cylinders is also widely used, such as combine harvesters, tractors and so on.